News

Video Conference With Atlas Copco On April 21st

Apr 22, 2022 Leave a message

After the first video conference on March, Atlas Copco and Biglux established an initial cooperation. The Atlas Copco team expressed concerns about many aspects of BIGLUX mobile solar light tower products. In response, the BIGLUX team answered one by one, focusing on the following points:

1. Lithium battery working temperature. 

2. Shipping packaging. 

3. Quality.

4. Upgrated cuboid solar tower can adjust the angle of the panel.

In addition to the answers in the meeting, the details will be sent to the Atlas Copco team by email in the form of document.

_20220422213543

  1. Lithium battery working temperature

    Atlas Copco concerned about the working temperature of Lithium battery, wondering that the lithium battery can't work in extreme cold weather. In this regard, we will fully understand where the product is to be deployed and evaluate the local climate, sunshine hours, and other factors before customers placing order. If the product is to be used in cold areas, we can add heaters to the batteries and equipments. 

    We have to ackowledge that the lithium battery have to work at the environment temperature over 0 ℃, The battery capacity is low at low temperature, which affects its performance. The cycle life of the lithium battery is greatly shortened at high temperature, and safety problems can also arise when the temperature is too high. Furthermore, lithium-ion batteries also present a safety hazard when charging below 0°C.

    For power battery systems, the consistency of cells and battery modules is crucial. The battery inevitably generates heat during use, which leads to an increase in the battery temperature. Due to the different positions of the cells or battery modules, the heat dissipation is different, resulting in different temperatures. The difference in temperature in turn leads to inconsistent performance of cells and modules.

    It can be seen that it is very necessary to thermally manage the battery pack so that it can work in the best working range as much as possible, improve its consistency, prolong its service life, avoid safety problems, etc. At this stage, it is impossible to keep the temperature of the battery pack at the same point, but it is completely possible to make it operate within a certain temperature range. The BMS controls the temperature by controlling the heating device and the cooling device, and incorporates the upper and lower thresholds of the temperature into the control range of the circuit breaker of the battery pack, thereby avoiding thermal runaway.

    Heat dissipation:

    During the charging and discharging process, the integrated resistance overcurrent generates heat, and when the battery pack continues to generate high current and overcurrent, the temperature of the battery pack continues to rise. When the temperature reaches the high temperature alarm temperature, the BMS turns on the fan to dissipate heat (generally set to 45°C to turn on the fan ) when the temperature drops to the fan-off temperature (usually set to 35°C).

    Heating:

    In some places, the temperature in winter is generally at minus ten degrees or even dozens of degrees. Although the lithium iron phosphate battery can still work at minus 40 degrees Celsius, the battery performance at low temperature (below 5 degrees Celsius) is greatly reduced, mainly in the capacity, At this time, the battery pack needs to be heated, generally using a heating belt. The heat-on temperature was set to 5°C, and the heat-off temperature was set to 25°C.

    In order to avoid thermal runaway caused by component failure, the BMS has introduced a maximum cut-off temperature, and the system will design the logic value of this value to generally not exceed 75 °C, usually set to 65 °C.

    Some laboratories now use phase change materials (PCM) for temperature regulation. Some materials undergo a phase transition (melting or solidification) at a certain temperature, with endothermic or exothermic heat. If a phase change material with a suitable temperature is found, the latent heat of the phase change is relatively large, and it is a suitable choice for a battery thermal management material. This solution is like putting cool and warm "clothes" on the battery pack. Lithium iron phosphate batteries need to choose materials with a melting point of 35 °C. When the battery temperature is higher than 35 °C, PMC melts and absorbs heat, so that the battery temperature is maintained below 35 °C (the amount of PMC is sufficient), and when the night temperature drops below 35 °C , the PCM material solidifies back. This allows the thermal management of the battery to take advantage of day and night temperature changes.

    When designing the battery pack and BMS temperature control, it is necessary to consider the volume and heat dissipation conditions of the battery pack, as well as waterproofing. In many cases, the battery pack not only relies on the BMS and external accessories to implement thermal management, but also needs to consider ventilation, heat dissipation and winter from the overall structure to keep warm.


  2. Shipping package.

    Since the product mast is available in various lengths, the packing method is related to the mast length. Towbars will be put and packaged under the trailers; the telescopic mast with 9M and 12M will be packaged separately in the wooden box, the mast under 9M will be assembly on the trailer while packaging. And the number of goods differs and so does the way of packing, for samples shipped by LCL, the trailers are full assembly packaged by wooden boxes.

    transport


  3. Quality:

BIGLUX is innovation driven and quality oriented company, we have strict quality control process and very professional high quality material selection systems. our high quality can be rooted from some details, for example:
1)Good powder and double powder coating for anti-corrosion.

2)Galvnized steel square Mast with 8mm diameter SUS316 lifting rope.

3)All the screws are SUS316 for the whole trailers.

4) All the materials we are using are high quality and  top-brand , such as LONGI solar panel, EPEVER and Morning Star MPPT to reach the higher efficiency of the whole solar system.

MPPT

  1. Upgrated cuboid solar tower can adjust the angle of solar panel.

    Currently, cuboid solar tower solar panels can only be stored and unfolded at 90 degrees horizontally. This may lead to the problem of not achieving the perfect sunlight angle in some cases, and it is Atlas copco team concerned about. Thank them for their questions, which will be an inspiration for us to improve our products. The original design has been improved by adding segmented movable joints so as to adapt to the angle of sunlight exposure in different areas or times. It's just finished simulation and design, ready to produce a sample. We will update to our website once it's finished.


These are the main contents of video conference on April 21st. We will follow up with them, and we are also looking forward to more business partner. We believe that the market for solar energy in the future will be very large, please feel free to contact us.

Send Inquiry